Guide

How to Remove a Schlage Deadbolt Lock

Updated on · By the Warlockery team

Here's how to remove a Schlage deadbolt lock: unscrew the interior thumb turn and cover plate first, then slide the exterior cylinder out and pull the bolt free from the edge of the door. The whole job takes about 15 minutes with a Phillips screwdriver.

On this page (8 sections)
  1. What tools do you need to remove a Schlage deadbolt?
  2. How do you remove the interior thumb turn and cover?
  3. How do you pull the cylinder and bolt out?
  4. How do you handle a deadbolt that won't come apart?
  5. How do you prep the door for a new lock?
  6. Can you replace a Schlage deadbolt with a keypad lock?
  7. What should you check before you buy the new lock?
  8. How do you remove a Schlage deadbolt safely and finish the job?

Here's how to remove a Schlage deadbolt lock: unscrew the interior thumb turn and cover plate first, then slide the exterior cylinder out and pull the bolt free from the edge of the door. The whole job takes about 15 minutes with a Phillips screwdriver and no special tools.

The order matters more than the force. Work from the inside of the door outward, keep the screws in a bag, and the lock comes apart without scratches or a bent bolt.

What tools do you need to remove a Schlage deadbolt?

A Phillips screwdriver is the main tool, and most Schlage deadbolts need nothing else. Add a small flathead, a bag for screws, and a cloth if the lock has been in place for years.

Schlage uses Phillips screws on the interior trim and on the bolt face, so a #2 driver fits most models. A stubby driver helps in tight spots near the door edge.

You may also want painter's tape to mark the door's position on the frame. The marks make it easier to line up the new lock later without guessing.

Skip a power driver on the trim screws. The torque can chew the screw head or crack a plastic cover, and these screws are short enough to turn by hand.

A thin flathead earns its place too. It lifts a painted-on cover plate without marking the door, and it can scrape old paint from the bolt face before you pull the bolt out.

Keep a rag nearby as well, since old locks shed grit and paint flakes onto the floor once the trim comes off.

How do you remove the interior thumb turn and cover?

Open the door and unscrew the two screws under the interior thumb turn, then lift the cover plate away from the door. This step exposes the cylinder and the tailpiece that links the two halves.

Hold the exterior cylinder with one hand while you loosen the last screw so it doesn't drop onto the floor. Set the thumb turn and cover aside in one place.

On some Schlage models the cover clips on over the screws. Grip the edge and pull it straight off rather than prying at the keyhole side.

If the cover sticks to paint or a gasket, slide a flathead under the edge and twist gently. Don't lever against the door face, which can mark the finish.

Where does the tailpiece go when the trim comes off?

The tailpiece is the flat bar that runs from the thumb turn through the door into the cylinder. It stays with the interior half on most Schlage models, so keep the thumb turn level as it comes away.

If the bar slides out, set it with the screws rather than on the floor. A tailpiece that falls into the bore hole is awkward to fish out, and a lost one means the lock won't line up if you refit it.

How do you pull the cylinder and bolt out?

Slide the exterior cylinder out from the outside face, then remove the two screws on the bolt face at the door edge. The bolt then pulls straight out of the bore hole.

The tailpiece sits between the cylinder and the thumb turn. Once the interior side is free, the cylinder slides toward you from the outside.

Support the cylinder as it comes out so it doesn't swing on the key or scratch the door. If the cylinder feels stuck, check for a set screw on the side of the trim before pulling harder.

Take out the edge screws last and keep them with the bolt. The bolt may need a small wiggle to clear the hole if paint has built up around the face plate.

Work the bolt out straight rather than tilting it. A tilted pull can catch the edge of the mortise and chip the wood, which then needs filling before the new bolt sits flush.

How do you handle a deadbolt that won't come apart?

Stop and look before forcing anything. A Schlage deadbolt that resists removal usually has a stuck screw, a seized cylinder, or paint sealing the trim to the door.

Check each screw head for stripping. If a head is chewed, a rubber band between the driver and the screw can add grip, or a screw extractor can remove it.

Paint around the cover plate is a common cause. Score the edge with a utility knife, then try the cover again with light pressure.

If the key won't turn and the cylinder won't slide, the lock may be seized from age. In that case, removing it may need a locksmith, especially if the door is your only secure entry.

Watch for a bolt that turns but won't retract. That points to a broken tailpiece or a bolt jammed against the strike, and pulling harder can bend the door edge.

How do you prep the door for a new lock?

Clear the old paint and debris from the bore hole and the edge mortise, then test the new lock's fit before screwing anything down. A clean hole is the difference between a lock that turns smoothly and one that binds.

Wipe the hole with a cloth and check that the latch bolt moves freely in the edge cutout. Scrape loose paint from the face plate area with a plastic scraper, not a metal blade.

Hold the new lock's bolt in the hole and turn the thumb turn to confirm the throw clears the strike plate. If the new deadbolt is a keypad model, this is also the moment to check the cylinder length against the door thickness.

Mark the door edge with tape before removing the old lock if you plan to fit a different brand. The old screw holes rarely line up exactly with a new lock's plate.

Can you replace a Schlage deadbolt with a keypad lock?

Yes, and the removal steps above are the same starting point. A keypad deadbolt drops into the same 1⅝-inch or 2⅛-inch bore hole in most cases, so the old Schlage cylinder comes out and the new one goes in.

The main check is the backset, the distance from the door edge to the center of the hole. Schlage deadbolts are commonly set at 2⅜ inches or 2¾ inches, and keypad locks fit those same two settings.

Door thickness matters too. A standard 1¾-inch door takes the standard cylinder, while a thicker door needs a longer tailpiece that some keypad kits include.

If you're weighing a keypad lock against a smart lock that fits over your existing deadbolt, our guide to what is a retrofit smart lock explains when you can skip removal altogether. A retrofit option keeps the Schlage cylinder in place and adds a motorized thumb turn on the inside.

For a full replacement, our Schlage BE365 keypad deadbolt review covers one model that uses the same bore hole and fits the removal steps here. Compare that approach with the best retrofit smart locks if you'd rather not remove the lock at all.

What changes if the new lock is a retrofit?

With a retrofit lock, the cylinder and bolt stay in the door. The motorized thumb turn mounts over the interior half, so you only remove the old thumb turn and cover, not the cylinder or the edge screws.

That means less work and no risk of losing the tailpiece alignment. If you ever want the plain thumb turn back, the retrofit comes off and the original interior trim goes back on.

What should you check before you buy the new lock?

Measure the bore hole, the backset, and the door thickness before you order. These three numbers decide whether a new deadbolt fits without drilling.

Use a tape measure from the door edge to the center of the deadbolt hole for the backset. Check the hole diameter with a ruler across the opening, and measure the door's thickness at the edge.

Confirm the new lock's bolt throw matches the strike plate on the frame. A longer throw may need the strike plate moved, which is a separate job.

Check the keyway too if you want one key for the whole house. A keypad lock removes the key question entirely, which is one reason people swap out an old Schlage in the first place.

If the door bore sits at 1⅝ inches rather than 2⅛ inches, some kits need a spacer. Note that down along with the backset so you order the right version first time.

How do you remove a Schlage deadbolt safely and finish the job?

Remove the interior trim, slide the cylinder, take out the edge screws, and keep every part together. That's the whole process for how to remove a Schlage deadbolt lock, and it stays safe as long as you don't force a stuck screw or leave the door unprotected mid-job.

Keep the door closed and latched on another lock while the deadbolt is out. If the deadbolt was the only lock, plan the swap so the door is never left open, or have a helper stay home during the work.

Bag the screws with the old lock and store it if you might reuse it. Then fit the new lock, test the throw against the strike plate, and check the door closes without rubbing.

If you're removing a different brand next, our guide to how to remove a Kwikset deadbolt lock follows the same inside-out order with the small differences that brand adds. The habits carry over: work from the interior, support the cylinder, and keep the screws in one place.

Frequently asked questions

Do I need to remove the deadbolt to install a keypad lock?

Usually yes, because the keypad cylinder replaces the existing deadbolt in the same bore hole. Removing the Schlage deadbolt first gives you a clean hole to fit the new cylinder and latch.

Can I remove a Schlage deadbolt without taking the door off its hinges?

Yes. The deadbolt is held by two screws under the interior cover, so the door stays hung while you work.

Only remove the door if a stuck bolt or damaged screw forces you to lay it flat.

What if the deadbolt screws won't turn?

Apply steady pressure rather than force, since a stripped head makes the job harder. A screwdriver that fills the slot fully and a drop of penetrating oil left for a few minutes usually free a stiff screw.

Should I keep the old Schlage deadbolt after removing it?

Keep it if the door might need a plain deadbolt again, such as for a rental handover. Bag the screws with the lock so the parts stay together, and label the key if you store it.

Is removing a Schlage deadbolt a job for a locksmith?

Most Schlage deadbolts come off with a screwdriver and no locksmith. Call one if the cylinder is seized, the bolt is jammed in the frame, or the door or frame is damaged around the lock.

Can I reuse the old deadbolt later?

Yes, as long as the screws and bolt are intact and the door bore has not changed. Keep the cylinder and latch together, and test the fit before you rely on it.