Guide

How to Replace a Schlage Deadbolt Lock

Updated on · By the Warlockery team

To replace a Schlage deadbolt, remove the old lock and fit the new one in the same door holes with a screwdriver. Check the backset matches your door's 2-3/8 in or 2-3/4 in spacing, then test the thumbturn and key before you close the door.

On this page (9 sections)
  1. What tools do you need to replace a Schlage deadbolt?
  2. How do you remove the old deadbolt?
  3. How do you check the backset before you buy?
  4. How do you install the new Schlage deadbolt?
  5. How do you line up the strike plate?
  6. How do you set codes on a keypad Schlage deadbolt?
  7. Should you replace the deadbolt with a smart lock?
  8. What should you check before you close the door?
  9. How to replace a Schlage deadbolt lock: the short version

To replace a Schlage deadbolt, take the old lock off and fit the new one into the same door holes using only a screwdriver. The job is a straight hardware swap, so you don't need to remove the door or call a locksmith.

If you're changing the lock anyway, this is the moment to decide whether you want a key, a keypad or a full smart lock. The steps below work for any Schlage deadbolt, keyed or electronic.

Knowing how to replace a Schlage deadbolt lock yourself saves a service call and keeps your door's existing holes intact.

What tools do you need to replace a Schlage deadbolt?

You need a Phillips screwdriver, and that's usually it. A tape measure helps you confirm the backset and door thickness, and a small cup keeps the screws from rolling away.

Schlage deadbolts install with a screwdriver and no hardwiring. That applies to the mechanical models and to the electronic ones, so you won't be running new wires through the door.

The kit that comes in the box covers the mounting hardware and printed instructions, so there's nothing extra to buy before you start.

Have a helper or a door wedge handy if the door swings. With the lock off, the door is free to move, and a door that slams while the hardware is loose can chip the edge or bend the bolt.

Skip the drill on a straight swap. You only need one if the old lock used a different hole size or the door edge is damaged.

The Schlage cross bore on a standard door is a fixed size, which is why the same face holes work for a keyed deadbolt and an electronic one alike.

How do you remove the old deadbolt?

Unscrew the interior thumbturn plate first, then the exterior half, and slide the bolt out of the door edge. Keep the screws grouped by length as you go, since they rarely match.

Start with the door open. Hold the exterior half with one hand while you loosen the last interior screw so it doesn't drop.

Pull both halves away from the door and set them aside. Then remove the two screws holding the bolt in the door edge and slide the bolt out.

Our full walkthrough on how to remove a Schlage deadbolt lock covers the trickier cases, such as a stuck bolt or a lock with a stripped screw head. A keypad model comes off the same way as a keyed one, so the order above holds either way.

Wipe the door edge and the two face holes before fitting the new lock. Old paint or metal shavings can stop the new bolt from sitting flush.

If the old bolt leaves a mark in the paint, line the new bolt up with that mark rather than guessing at the height.

How do you check the backset before you buy?

Measure from the door edge to the center of the bolt hole. If it reads 2-3/8 in, you have a 2-3/8 in backset; if it reads 2-3/4 in, you have the deeper one.

Schlage deadbolts fit both backsets, so the same lock works on most standard doors. What changes is how the latch is set, and that's a quick adjustment on the bolt itself.

The BE365, for example, is built to take either backset, so you don't have to pick a version when you order.

Measure the door thickness too. Schlage lists a range of 1-3/8 in to 1-3/4 in for its deadbolts, which covers most interior and exterior doors.

The BE365 spec sheet gives that same 1-3/8 in to 1-3/4 in range, so the measurement holds across the family.

If your door falls outside that range, the bolt won't clamp correctly. Sort that before you order rather than after the old lock is off.

A thin panel door or an unusually thick exterior door is the case to watch for.

How do you install the new Schlage deadbolt?

Fit the bolt first, then the exterior and interior halves, then the strike. Set the latch to your measured backset before the bolt goes into the door.

  1. Slide the new bolt into the edge hole and drive its two screws.
  2. Set the exterior half against the door with the keyway or keypad facing out.
  3. Fit the interior plate and thumbturn, then start the mounting screws by hand.
  4. Tighten evenly, alternating sides so the two halves pull square.
  5. Test the thumbturn before you fit the strike.

Don't overtighten. A deadbolt that pinches the door will drag on the strike and wear the thumbturn, and the fix is usually a quarter turn back on each screw.

A keypad model like the BE365 goes on the same way. Its code setup happens after the hardware is in place.

On a keypad model, keep the keypad and the illuminated buttons facing the outside and the thumbturn on the inside, since the lock won't seat properly if the two halves are reversed.

How do you line up the strike plate?

Close the door and turn the thumbturn to see where the bolt lands. If the bolt hits the strike instead of sliding into it, the plate or the door needs a small adjustment.

Loosen the strike screws and shift the plate up, down or slightly in until the bolt drops in with the door closed. Then tighten it again.

Keep the strike square to the door edge so the bolt meets it straight on rather than at an angle.

If the bolt still catches, check that the door hasn't sagged. A door that rubs at the top will throw the bolt off at the strike no matter how you move the plate.

Don't file the strike as a first move. Adjust the plate and the door first, because filing metal is hard to undo.

Moving the plate by a fraction at a time and retesting is faster than guessing at how much material to take off.

How do you set codes on a keypad Schlage deadbolt?

Program your codes after the lock is mounted and the battery is in. The BE365 comes with 2 pre-programmed codes and lets you assign up to 19 for family and guests.

The keypad buttons light up when pressed, so you can enter a code in the dark. The numbers are silicone coated and wear resistant.

A 9V battery is included, and Schlage says typical use gets up to 2 years of battery life. The same lock also warns you when the battery runs low, so you aren't locked out without notice.

The BE365 uses a thumbturn on the inside and a keypad on the outside. You open from outside with a valid code and lock by pressing the Schlage button and turning the outside thumbturn.

Schlage backs the electronics for 3 years and the mechanical parts and finish for life.

If you want app control and remote access instead, the Schlage Encode connects to WiFi and manages up to 100 codes. It fits the same door holes as a standard deadbolt.

It runs on four AA batteries with up to six months of typical use, and it adds a built-in alarm for door movement and forced entry.

For a keyless model with no keyway at all, the Schlage Touch Deadbolt uses a touchscreen and includes a jumpstart feature for a dead battery. Its cylinder-free design means there's no keyway to bump or pick.

The slim profile helps it clear a screen door on the same opening.

Should you replace the deadbolt with a smart lock?

Yes, if you want codes, app control or auto-lock; no, if a plain keyed lock already does the job. A smart deadbolt is still a deadbolt, so the swap follows the same steps.

A retrofit smart lock is the lighter option. It keeps your existing deadbolt and adds keypad or app control on the interior side, which suits renters who can't change the hardware.

A full replacement gives you a cleaner result. You get a matched finish, a fresh bolt and a new warranty, and you avoid the bulk of an add-on unit on the inside of the door.

The Encode also brings features a retrofit kit can't match, like auto-lock with a selectable time delay and a customizable alarm built into the lock itself.

If you're unsure which route fits your door and lease, our explainer on what is a retrofit smart lock lays out the difference in plain terms.

Read the Schlage BE365 review before you decide between keypad and smart. It's the simplest step up from a keyed lock, and it installs in the same holes.

What should you check before you close the door?

Test the thumbturn, the key or code, and the bolt throw with the door open. Then close it and confirm the bolt slides into the strike without a push.

Check that the bolt extends fully. A bolt that stops short leaves the door insecure even though the thumbturn turns.

Try the lock from both sides. On a keyed model, the key should turn smoothly; on a keypad model, enter a code and confirm the Schlage button responds.

On the Touch, enter your code and confirm the touchscreen lights up and releases the bolt.

Finally, check the interior screws once more. Loose screws are the most common reason a new deadbolt feels stiff in the first week.

How to replace a Schlage deadbolt lock: the short version

Replacing a Schlage deadbolt comes down to four things: measure the backset, reuse the door holes, fit the bolt before the trim, and test the strike. A screwdriver and 15 to 30 minutes cover most doors.

Pick the Schlage BE365 if you want codes without WiFi. Go with the Schlage Encode for app and voice control, or the Schlage Touch Deadbolt if you'd rather have no keyway at all.

If you'd rather not remove your current lock, compare retrofit smart locks first. Either way, keep your old deadbolt and its screws together in case you move and need to put the original back.

Frequently asked questions

Do I need to drill new holes to swap a Schlage deadbolt?

Usually no. A Schlage deadbolt in the same size class lines up with the existing 2-1/8 in cross bore and the bolt hole, so you reuse the door's holes.

Drill only if the old lock used a different size or the holes are damaged.

What is a deadbolt backset and why does it matter?

The backset is the distance from the door edge to the center of the bolt hole, either 2-3/8 in or 2-3/4 in. Schlage deadbolts fit both, but you set the latch to match your door so the bolt lines up with the strike plate.

How long does it take to replace a deadbolt?

About 15 to 30 minutes with a screwdriver. Most of that time goes to lining up the bolt and strike, not to the lock body, which is why checking the backset and door thickness first saves the most time.

Can I replace a deadbolt without removing the door?

Yes. Leave the door hung and work from both faces.

Support the door slightly while the lock is off, keep screws in a cup so they don't roll, and never let the door swing free with the hardware loose.

Do I need to keep a key if I fit a keypad Schlage deadbolt?

No. A keypad model like the Schlage BE365 uses codes, and the Schlage Touch has no keyway at all.

Check your home insurance and any rental agreement first, since some policies ask for a physical key override.