How to Program a Veise Fingerprint Door Lock

On this page (9 sections)

1. What should you do before you program the lock?
2. How do you enter admin mode on a Veise lock?
3. How do you register a fingerprint?
4. How do you add passcodes to the same lock?
5. Which features should you set while you're in the menu?
6. How do you test and manage the entries you programmed?
7. Should you pick a Veise lock or a model with app control?
8. How do you reset the lock if programming goes wrong?
9. The bottom line on programming a Veise fingerprint door lock

To program a Veise fingerprint door lock, wake the keypad, enter admin mode with the default or your changed admin code, then follow the voice prompts to add each fingerprint or passcode. Save and test every entry from outside the door before you rely on it.

Programming is a menu walk, not a wiring job. Once you know the admin code and the order of the prompts, adding a fingerprint takes under a minute per finger.

What should you do before you program the lock?

Set the lock up and change the factory admin code first. Programming works from the admin menu, so the code you use to reach it matters more than any other step.

Install the lock and confirm the deadbolt throws smoothly by hand or key. Program the lock with the door open so you can't lock yourself out if a step goes wrong.

Look for the factory admin code in the manual or on the sticker inside the battery cover. Most Veise locks ship with 123456, and leaving it unchanged means anyone who knows the default can open your admin menu.

Change it to a code only you know before you add fingerprints. Keep a written record somewhere safe, since a forgotten admin code means a factory reset.

Our guide to how a keyless door lock works covers the electronics behind the keypad and sensor if you want the background first.

How do you enter admin mode on a Veise lock?

Touch the keypad to wake it, then key in the admin code and press the open or # key. The lock confirms with a voice prompt or a short tone when you're in the menu.

Start with the door open and the keypad lit. Press the wake key or touch the numbers, then enter the admin code.

Some models want a # after the code, and others want the checkmark key.

Listen for the spoken menu. Most Veise locks announce numbered options for adding users, deleting users, setting auto-lock and changing settings.

Write the option numbers down so you don't have to replay the menu each time.

If the keypad stays dark, check the batteries first. A weak battery pack can drop the lock out of admin mode partway through programming.

How do you register a fingerprint?

Pick the add-user option, choose a free user number, then press the same finger three to five times as the sensor asks. The lock saves the print when it confirms the last press.

Clean the sensor with a dry cloth and dry your finger before you start. Damp or dusty skin is the most common reason a print won't save.

Use the finger you'd naturally reach for on the handle, usually the index or thumb. Press firmly and center the pad on the sensor, lifting fully between reads.

Vary the angle slightly on the later presses so the stored print covers more of your fingertip. A flat, identical press each time gives the lock less to match against.

Repeat the process for each family member under their own user number. Separate numbers let you delete one person's access later without touching anyone else's.

How many fingerprints should you add?

Add one finger per person who lives in the home, plus a second finger for anyone who comes and goes daily. A backup finger saves you when a cut or a bandage covers your main print.

Aim for 2 prints per regular user on different hands. That gives the sensor a clean alternative if one finger is scraped, wet or covered.

Guests and cleaners don't need a fingerprint. Give them a temporary passcode instead, and delete it when the visit ends.

How do you add passcodes to the same lock?

Return to the admin menu, choose the passcode option, pick a user slot, then type the code twice. The lock repeats it back or confirms with a tone before saving.

Passcodes cover the people who shouldn't have a fingerprint stored, like a dog sitter or a delivery helper. Give each person their own code so you can remove one without redoing the others.

Many Veise locks support one-time codes or scheduled codes. Use a one-time code for a single visit and it expires after one use.

Avoid codes built from your address, birthday or phone digits. If the keypad shows wear on certain numbers, wipe it down now and then to blur the pattern.

If you move to a different brand later, our walkthrough on how to change a keypad door lock code covers the general steps.

Which features should you set while you're in the menu?

Set auto-lock, the open direction and the volume while the admin menu is already open. These settings decide how the lock behaves day to day, so handle them in the same session.

Auto-lock relocks the deadbolt a set number of seconds after opening. It suits households with kids or anyone who forgets to lock behind them.

Set a delay long enough to get inside with groceries, often 10 to 30 seconds.

Check the open direction if the deadbolt turns the wrong way. The setting swaps the motor direction so a thumb turn or app command locks rather than opens.

Turn the voice volume down or off if the prompts wake the house. Keep it on while you're learning the menu, then quiet it once everyone's prints and codes are saved.

How do you test and manage the entries you programmed?

Close the door and test every fingerprint and code from outside, one person at a time. A print that saved in the menu can still fail on a real, quick touch.

Try each finger the way you'd actually use it in a hurry, without lining up the sensor carefully. A slow, deliberate press hides a print that's too shallow to match.

Test the key as well, and keep a spare key outside the house in a lockbox. If the battery dies, the key is your way in.

Delete old entries when someone moves out or a contractor's job ends. Enter admin mode, choose delete user, then remove that user's number.

Review the user list every few months so a code you gave a plumber last year isn't still active. Programming a lock is only as safe as the list of people who can open it.

Should you pick a Veise lock or a model with app control?

A Veise keypad lock is a solid choice if you want local fingerprint and code access without an app. If you want remote opening, schedules from your phone and entry history, a Wi-Fi lock fits better.

Veise locks work at the door itself. That means no bridge, no account and no cloud connection, which some households prefer.

You manage users from the keypad and its voice prompts.

App-connected locks add remote control and logs. The eufy C220 pairs built-in Wi-Fi with a self-learning fingerprint sensor that sharpens with each touch.

The Tapo DL110 stores up to 100 fingerprints and opens in about 0.42 seconds. The Wyze Lock Bolt v2 opens in about 0.5 seconds and adds auto-lock plus a USB-C backup for a dead battery.

If you're still comparing lock styles, see our guide to smart door handle locks and how they differ from deadbolts. And read how to choose a keyless door lock before you decide on fingerprint, keypad or app control.

How do you reset the lock if programming goes wrong?

Run a factory reset from the admin menu or the reset button inside the battery cover, then reprogram from the default admin code. Reset wipes every fingerprint and passcode, so have everyone re-register afterward.

Press and hold the reset button as the manual directs, often for 5 seconds, until the lock announces a reset. Some models offer a reset option in the admin menu instead.

After the reset, the admin code returns to the factory default. Change it again before you add prints, or the lock stays open to anyone who knows the default.

Check the deadbolt and the keypad response after a reset. If the lock still ignores the keypad or won't save prints, replace the batteries and try once more before contacting support.

The bottom line on programming a Veise fingerprint door lock

Learning how to program a Veise fingerprint door lock comes down to four habits: change the admin code, add prints one finger at a time, give guests codes rather than fingerprints, and delete access when it should end. Test every entry from outside with the door shut before you trust it.

If you want local keypad control, a Veise lock covers it. If remote opening and an activity log matter more, the eufy C220, Tapo DL110 and Wyze Lock Bolt v2 are the app-connected options worth comparing.

Measure your door and confirm the deadbolt fits before you order.

Frequently asked questions

What is the default admin code on a Veise fingerprint door lock?

Most Veise locks ship with a factory admin code of 123456, which you should change right after setup. If that code doesn't open admin mode, look on the sticker inside the battery cover or in the included manual for the model's factory code.

How many fingerprints can a Veise lock store?

The count varies by model, but most Veise fingerprint locks store 50 to 100 fingerprints, grouped by user number. Register one finger twice, from slightly different angles, so a quick or damp touch still reads cleanly.

How do I delete a fingerprint or code I no longer want?

Enter admin mode, choose the delete-user option the voice prompt names, then select the user number or scan the finger you want removed. Delete codes for former roommates or contractors as soon as access should end, rather than leaving them active.

Why won't my Veise lock accept a new fingerprint?

Wipe the sensor and your finger dry first, since moisture and dust blur the ridges the sensor reads. Register the same finger as a fresh user with a firm, centered press, and replace the batteries if the lock resets mid-programming.